美文网首页
静态路由配置

静态路由配置

作者: 潘俊百 | 来源:发表于2018-11-08 17:31 被阅读0次
TIM截图20181108165303.jpg

配置R1各个端口ip

[R1]interface GigabitEthernet 0/0/0
[R1-GigabitEthernet0/0/0]ip address 192.168.100.1 24
on the interface GigabitEthernet0/0/0 has entered the UP state. 
[R1-GigabitEthernet0/0/0]qu 
[R1]interface GigabitEthernet 0/0/1
[R1-GigabitEthernet0/0/1]ip address 192.168.101.2 24
[R1-GigabitEthernet0/0/1]qu
[R1]interface LoopBack 0
[R1-LoopBack0]ip address 192.168.201.1 24
[R1-LoopBack0]qu
[R1]display ip interface brief 
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 4
The number of interface that is DOWN in Physical is 1
The number of interface that is UP in Protocol is 4
The number of interface that is DOWN in Protocol is 1

Interface                         IP Address/Mask      Physical   Protocol  
GigabitEthernet0/0/0              192.168.100.1/24     up         up        
GigabitEthernet0/0/1              192.168.101.2/24     up         up        
GigabitEthernet0/0/2              unassigned           down       down      
LoopBack0                         192.168.201.1/24     up         up(s)     
NULL0                             unassigned           up         up(s) 

配置R2各个端口ip

[R2]interface GigabitEthernet 0/0/0
[R2-GigabitEthernet0/0/0]ip address 192.168.100.2 24
[R2-GigabitEthernet0/0/0]qu
[R2]interface GigabitEthernet 0/0/2
[R2-GigabitEthernet0/0/2]ip address 192.168.102.1 24
[R2-GigabitEthernet0/0/2]qu
[R2]interface LoopBack 0
[R2-LoopBack0]ip address 192.168.202.1 24
[R2-LoopBack0]qu    
[R2]display ip interface brief 
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 4
The number of interface that is DOWN in Physical is 1
The number of interface that is UP in Protocol is 4
The number of interface that is DOWN in Protocol is 1

Interface                         IP Address/Mask      Physical   Protocol  
GigabitEthernet0/0/0              192.168.100.2/24     up         up        
GigabitEthernet0/0/1              unassigned           down       down      
GigabitEthernet0/0/2              192.168.102.1/24     up         up        
LoopBack0                         192.168.202.1/24     up         up(s)     
NULL0                             unassigned           up         up(s)  

配置R3各个端口ip

[R3]interface GigabitEthernet 0/0/1
[R3-GigabitEthernet0/0/1]ip address 192.168.101.1 24
[R3-GigabitEthernet0/0/1]qu
[R3]interface GigabitEthernet 0/0/2
[R3-GigabitEthernet0/0/2]ip address 192.168.102.2 24
[R3-GigabitEthernet0/0/2]qu
[R3]interface LoopBack 0
[R3-LoopBack0]ip address 192.168.203.1 24
[R3-LoopBack0]qu
[R3]display ip interface brief 
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 4
The number of interface that is DOWN in Physical is 1
The number of interface that is UP in Protocol is 4
The number of interface that is DOWN in Protocol is 1

Interface                         IP Address/Mask      Physical   Protocol  
GigabitEthernet0/0/0              unassigned           down       down      
GigabitEthernet0/0/1              192.168.101.1/24     up         up        
GigabitEthernet0/0/2              192.168.102.2/24     up         up        
LoopBack0                         192.168.203.1/24     up         up(s)     
NULL0                             unassigned           up         up(s)     

配置静态路由

在R1上面配置到R2 192.168.102.0/24 网段的静态路由

[R1]ip route-static 192.168.102.0 24 192.168.100.2
[R1]display ip routing-table 
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
         Destinations : 14       Routes : 14       

Destination/Mask    Proto   Pre  Cost      Flags NextHop         Interface

      127.0.0.0/8   Direct  0    0           D   127.0.0.1       InLoopBack0
      127.0.0.1/32  Direct  0    0           D   127.0.0.1       InLoopBack0
127.255.255.255/32  Direct  0    0           D   127.0.0.1       InLoopBack0
  192.168.100.0/24  Direct  0    0           D   192.168.100.1   GigabitEthernet
0/0/0
  192.168.100.1/32  Direct  0    0           D   127.0.0.1       GigabitEthernet
0/0/0
192.168.100.255/32  Direct  0    0           D   127.0.0.1       GigabitEthernet
0/0/0
  192.168.101.0/24  Direct  0    0           D   192.168.101.2   GigabitEthernet
0/0/1
  192.168.101.2/32  Direct  0    0           D   127.0.0.1       GigabitEthernet
0/0/1
192.168.101.255/32  Direct  0    0           D   127.0.0.1       GigabitEthernet
0/0/1
  192.168.102.0/24  Static  60   0          RD   192.168.100.2   GigabitEthernet
0/0/0
  192.168.201.0/24  Direct  0    0           D   192.168.201.1   LoopBack0
  192.168.201.1/32  Direct  0    0           D   127.0.0.1       LoopBack0
192.168.201.255/32  Direct  0    0           D   127.0.0.1       LoopBack0
255.255.255.255/32  Direct  0    0           D   127.0.0.1       InLoopBack0

使用ping命令测试网络是畅通

[R1]ping 192.168.102.1
  PING 192.168.102.1: 56  data bytes, press CTRL_C to break
    Reply from 192.168.102.1: bytes=56 Sequence=1 ttl=255 time=50 ms
    Reply from 192.168.102.1: bytes=56 Sequence=2 ttl=255 time=30 ms
    Reply from 192.168.102.1: bytes=56 Sequence=3 ttl=255 time=30 ms
    Reply from 192.168.102.1: bytes=56 Sequence=4 ttl=255 time=20 ms
    Reply from 192.168.102.1: bytes=56 Sequence=5 ttl=255 time=10 ms

  --- 192.168.102.1 ping statistics ---
    5 packet(s) transmitted
    5 packet(s) received
    0.00% packet loss
    round-trip min/avg/max = 10/28/50 ms

模拟R1与R2之间出现故障,通过备份路由R1访问R2的192.168.102.0/24网段

在R1上添加备份路由(添加后,路由表未发生变化,因为优先级为80比默认的之恋路由优先级低)

[R1]ip route-static 192.168.102.0 24 192.168.101.1 preference 80

在R2添加路由

[R2]ip route-static 192.168.101.0 24 192.168.102.2

删除R1和R2之间的连接线后路由表变化

[R1]display ip routing-table 
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
         Destinations : 11       Routes : 11       

Destination/Mask    Proto   Pre  Cost      Flags NextHop         Interface

      127.0.0.0/8   Direct  0    0           D   127.0.0.1       InLoopBack0
      127.0.0.1/32  Direct  0    0           D   127.0.0.1       InLoopBack0
127.255.255.255/32  Direct  0    0           D   127.0.0.1       InLoopBack0
  192.168.101.0/24  Direct  0    0           D   192.168.101.2   GigabitEthernet
0/0/1
  192.168.101.2/32  Direct  0    0           D   127.0.0.1       GigabitEthernet
0/0/1
192.168.101.255/32  Direct  0    0           D   127.0.0.1       GigabitEthernet
0/0/1
  192.168.102.0/24  Static  80   0          RD   192.168.101.1   GigabitEthernet
0/0/1
  192.168.201.0/24  Direct  0    0           D   192.168.201.1   LoopBack0
  192.168.201.1/32  Direct  0    0           D   127.0.0.1       LoopBack0
192.168.201.255/32  Direct  0    0           D   127.0.0.1       LoopBack0
255.255.255.255/32  Direct  0    0           D   127.0.0.1       InLoopBack0

测试R1能否达到R2的192.168.102.0/24网段

[R1]ping 192.168.102.1
  PING 192.168.102.1: 56  data bytes, press CTRL_C to break
    Reply from 192.168.102.1: bytes=56 Sequence=1 ttl=254 time=30 ms
    Reply from 192.168.102.1: bytes=56 Sequence=2 ttl=254 time=40 ms
    Reply from 192.168.102.1: bytes=56 Sequence=3 ttl=254 time=20 ms
    Reply from 192.168.102.1: bytes=56 Sequence=4 ttl=254 time=20 ms
    Reply from 192.168.102.1: bytes=56 Sequence=5 ttl=254 time=30 ms

  --- 192.168.102.1 ping statistics ---
    5 packet(s) transmitted
    5 packet(s) received
    0.00% packet loss
    round-trip min/avg/max = 20/28/40 ms

相关文章

  • 锐捷实战系列(三十八) 静态路由

    实训目的 学习静态路由的原理。 学习静态路由的优缺点。 学习静态路由的配置使用。 实训背景 静态路由 静态路由是指...

  • CCNA-13、静态路由

    何时使用静态路由-路由器较少-唯一外连出口-星型拓扑 !静态路由它配置完是不会自己修改的, 配置静态路由 路由表中...

  • HCNA-静态路由

    静态路由配置实例 1.配置思路 在路由器R1上配置一条静态路由,目的地/掩码是2.0.0.0/8,下一跳I...

  • 逸佳君:CCNA之静态路由实验

    静态路由实验 拓扑图: 实验要求: 1、只用静态路由,使得全网都能通信 2、配置RIPv2,使的静态路由成为备份路...

  • 路由选择之静态路由

    路由的几种来源 直连路由 静态路由 动态路由 静态路由简介 是一种需要管理员手工配置的特殊路由,在不同网络环境中有...

  • 2018-01-02

    静态路由配置与管理实验报告 ...

  • 静态路由配置(HCNA网络技术实验指南)

    静态路由配置 1、实验要求:PC1和PC2之间有三台路由器,需要在三台路由器上配置静态路由,确保PC1可以ping...

  • vue项目配置404项目

    静态路由,在router.js中配置理由信息 动态路由:不要再静态路由中添加404页面,在addRoutes里进行...

  • 2019-08-06

    day 26 操作系统基础网络章节 课程介绍 1.掌握路由配置方法配置动态路由 配置静态默认路由2.掌握网络架构...

  • 静态路由实验

    静态路由优点 对路由器CPU没有管理性开销 在路由器间没有带宽占用 安全稳定 静态路由缺点 对于新添网络配置繁琐,...

网友评论

      本文标题:静态路由配置

      本文链接:https://www.haomeiwen.com/subject/xdwwxqtx.html