直接 copy 过来，https://itsfoss.com/connect-wifi-terminal-ubuntu/
Step 1: Identify your wireless network interface name
There are several ways to identify your network interface name. You can use the ip command, the deprecated ipconfig command or check this file:
ls /sys/class/net
This should give you all the available networking interface (Ethernet, wifi and loopback). The wireless network interface name starts with ‘w’ and it is usually named similar to wlanX, wlpxyz.
abhishek@itsfoss:~$ ls /sys/class/net
eth0 lo wlan0
Take a note of this interface name. You’ll use it in the next step.
Step 2: Edit the Netplan configuration file with the wifi interface details
The Netplan configuration file resides in /etc/netplan directory. If you check the contents of this directory, you should see files like 01-network-manager-all.yml or 50-cloud-init.yaml.
If it is Ubuntu server, you should have cloud-init file. For desktops, it should be network-manager file.
The Network Manager on the Linux desktop allows you to choose a wireless network. You may hard code the wifi access point in its configuration. This could help you in some cases (like suspend) where connection drops automatically.
Whichever file it is, open it for editing. I hope you are a tad bit familiar with Nano editor because Ubuntu comes pre-installed with it.
sudo nano /etc/netplan/50-cloud-init.yaml
YAML files are very sensitive about spaces, indention and alignment. Don’t use tabs, use 4 (or 2, whichever is already used in the YAML file) spaces instead where you see an indention.
Basically, you’ll have to add the following lines with the access point name (SSID) and its password (usually) in quotes:
wifis:
wlan0:
dhcp4: true
optional: true
access-points:
"SSID_name":
password: "WiFi_password"
Again, keep the alignment as I have shown or else YAML file won’t be parsed and it will throw an error.
Your complete configuration file may look like this:
# This file is generated from information provided by the datasource. Changes
# to it will not persist across an instance reboot. To disable cloud-init's
# network configuration capabilities, write a file
# /etc/cloud/cloud.cfg.d/99-disable-network-config.cfg with the following:
# network: {config: disabled}
network:
ethernets:
eth0:
dhcp4: true
optional: true
version: 2
wifis:
wlan0:
dhcp4: true
optional: true
access-points:
"SSID_name":
password: "WiFi_password"
I find it strange that despite the message that changes will not persist across an instance reboot, it still works.
Anyway, generate the configuration using this command:
sudo netplan generate
And now apply this:
sudo netplan apply
If you are lucky, you should have network connected. Try to ping a website or run apt update command.
However, things may not go as smooth and you may see some errors. Try some extra steps if that’s the case.
Possible troubleshooting
It is possible that when you use the netplan apply command, you see an error in the output that reads something like this:
Failed to start netplan-wpa-wlan0.service: Unit netplan-wpa-wlan0.service not found.
Traceback (most recent call last):
File "/usr/sbin/netplan", line 23, in <module>
netplan.main()
File "/usr/share/netplan/netplan/cli/core.py", line 50, in main
self.run_command()
File "/usr/share/netplan/netplan/cli/utils.py", line 179, in run_command
self.func()
File "/usr/share/netplan/netplan/cli/commands/apply.py", line 46, in run
self.run_command()
File "/usr/share/netplan/netplan/cli/utils.py", line 179, in run_command
self.func()
File "/usr/share/netplan/netplan/cli/commands/apply.py", line 173, in command_apply
utils.systemctl_networkd('start', sync=sync, extra_services=netplan_wpa)
File "/usr/share/netplan/netplan/cli/utils.py", line 86, in systemctl_networkd
subprocess.check_call(command)
File "/usr/lib/python3.8/subprocess.py", line 364, in check_call
raise CalledProcessError(retcode, cmd)
subprocess.CalledProcessError: Command '['systemctl', 'start', '--no-block', 'systemd-networkd.service', 'netplan-wpa-wlan0.service']' returned non-zero exit status 5.
It is possible that wpa_supplicant service is not running. Run this command:
sudo systemctl start wpa_supplicant
Run netplan apply once again. If it fixes the issue well and good. Otherwise, shutdown your Ubuntu system using:
shutdown now
Start your Ubuntu system again, log in and generate and apply netplan once again:
sudo netplan generate
sudo netplan apply
It may show warning (instead of error) now. It is warning and not an error. I checked the running systemd services and found that netplan-wpa-wlan0.service was already running. Probably it showed the warning because it was already running and ‘netplan apply’ updated the config file (even without any changes).
Warning: The unit file, source configuration file or drop-ins of netplan-wpa-wlan0.service changed on disk. Run 'systemctl daemon-reload' to reload units.
It is not crtical and you may check that the internet is probably working already by running apt update.
I hope you were able to connect to wifi using the command line in Ubuntu with the help of this tutorial. If you are still facing trouble with it, do let me know in the comment section.
网友评论