1.编写如下源代码
`timescale 1ns / 1ps
module top(
input clk,
input rst,
output test_clk,
input [1:0] switch,
output [3:0] r,g,b,
output hs,vs
);
wire clk40M, clk25M;
// rst = 0
assign test_clk = (rst) ? clk40M : clk25M;
// 100MHz x10 --> 1000MHz
// 800~1600,
PLLE2_BASE #(
.BANDWIDTH("OPTIMIZED"), // OPTIMIZED, HIGH, LOW
.CLKFBOUT_MULT(10), // Multiply value for all CLKOUT, (2-64)
.CLKFBOUT_PHASE(0.0), // Phase offset in degrees of CLKFB, (-360.000-360.000).
.CLKIN1_PERIOD(10.0), // Input clock period in ns to ps resolution (i.e. 33.333 is 30 MHz).
// CLKOUT0_DIVIDE - CLKOUT5_DIVIDE: Divide amount for each CLKOUT (1-128)
.CLKOUT0_DIVIDE(25), // 40M
.CLKOUT1_DIVIDE(40), // 25M
.CLKOUT2_DIVIDE(1),
.CLKOUT3_DIVIDE(1),
.CLKOUT4_DIVIDE(1),
.CLKOUT5_DIVIDE(1),
// CLKOUT0_DUTY_CYCLE - CLKOUT5_DUTY_CYCLE: Duty cycle for each CLKOUT (0.001-0.999).
.CLKOUT0_DUTY_CYCLE(0.5),
.CLKOUT1_DUTY_CYCLE(0.5),
.CLKOUT2_DUTY_CYCLE(0.5),
.CLKOUT3_DUTY_CYCLE(0.5),
.CLKOUT4_DUTY_CYCLE(0.5),
.CLKOUT5_DUTY_CYCLE(0.5),
// CLKOUT0_PHASE - CLKOUT5_PHASE: Phase offset for each CLKOUT (-360.000-360.000).
.CLKOUT0_PHASE(0.0),
.CLKOUT1_PHASE(0.0),
.CLKOUT2_PHASE(0.0),
.CLKOUT3_PHASE(0.0),
.CLKOUT4_PHASE(0.0),
.CLKOUT5_PHASE(0.0),
.DIVCLK_DIVIDE(1), // Master division value, (1-56)
.REF_JITTER1(0.0), // Reference input jitter in UI, (0.000-0.999).
.STARTUP_WAIT("FALSE") // Delay DONE until PLL Locks, ("TRUE"/"FALSE")
)
PLLE2_BASE_inst (
// Clock Outputs: 1-bit (each) output: User configurable clock outputs
.CLKOUT0(clk40M), // 1-bit output: CLKOUT0
.CLKOUT1(clk25M), // 1-bit output: CLKOUT1
.CLKOUT2(CLKOUT2), // 1-bit output: CLKOUT2
.CLKOUT3(CLKOUT3), // 1-bit output: CLKOUT3
.CLKOUT4(CLKOUT4), // 1-bit output: CLKOUT4
.CLKOUT5(CLKOUT5), // 1-bit output: CLKOUT5
// Feedback Clocks: 1-bit (each) output: Clock feedback ports
.CLKFBOUT(clkfb), // 1-bit output: Feedback clock
.LOCKED(LOCKED), // 1-bit output: LOCK
.CLKIN1(clk), // 1-bit input: Input clock 100M
// Control Ports: 1-bit (each) input: PLL control ports
.PWRDWN(1'b0), // 1-bit input: Power-down
.RST(1'b0), // 1-bit input: Reset
// Feedback Clocks: 1-bit (each) input: Clock feedback ports
.CLKFBIN(clkfb) // 1-bit input: Feedback clock
);
wire vga_clk = clk40M;
//800x600
parameter H_END = 10'd800;
parameter V_END = 10'd600;
reg [9:0] h_cnt = 0;
reg [9:0] v_cnt = 0;
always@(posedge vga_clk or posedge rst) begin
if (rst) begin
h_cnt <= 10'b0;
v_cnt <= 10'b0;
end
else if (h_cnt==H_END) begin
h_cnt <= 10'b0;
if(v_cnt == V_END)
v_cnt <= 10'b0;
else
v_cnt <= v_cnt + 1'b1;
end
else
h_cnt <= h_cnt + 1'b1;
end
assign hs = (h_cnt==H_END);
assign vs = (v_cnt==V_END);
endmodule
2.添加testbench。选择Add soruces -> Add or create simulation sources
picture
3.Create File，然后输入tb，点OK
picture
4.编写testbench代码，如下：
`timescale 1ns / 1ps
module tb();
reg clk100M;
reg rst;
wire test_clk;
wire hs,vs;
top uut(
.clk(clk100M),
.rst(rst),
.test_clk(test_clk),
.switch(),
.r(),
.g(),
.b(),
.hs(hs),
.vs(vs)
);
initial begin
clk100M = 0;
forever begin
#5 clk100M=~clk100M;
end
end
initial begin
rst = 1;
#100;
rst = 0;
#100000 $finish;
end
endmodule
5.选择Simulation-> Run Behavioral Simulation
picture
完了之后，可以看到类似下面的界面：
picture
6.添加要观察的信号到波形中。选中uut，可以看到uut中的信号都列出来了
picture
选中要观察的信号，按shift或ctrl可以多选。右键->Add to Wave，即可。如图，添加了v_cnt和h_cnt两个信号。
picture
7.点击图中的Run All，则运行仿真，直到弹出来仿真停止的位置
picture
picture
8.如果要继续仿真，再次点击Run All。要停止，按暂停
picture
9.按过暂停后，可以修改top.v代码或tb.v代码。修改完后，要再次仿真，直接按Relaunch Simulation
picture
网友评论