美文网首页我爱编程
arduino通过ENC28J60连接以太网

arduino通过ENC28J60连接以太网

作者: s7_200_smart | 来源:发表于2016-05-02 11:44 被阅读1161次
    **enc28j60**
    • 1 先把arduino 的IDE装好
    • 2 下载EtherCard库文件【下载地址

    EtherCard is a driver for the ENC28J60 chip, compatible with Arduino IDE. Adapted and extended from code written by Guido Socher and Pascal Stang.

    EtherCard是ENC28J60芯片的一种驱动,与Arduino的开发环境兼容。项目借鉴并扩展了Guido Socher与Pascal Stang的代码。

    • 3 添加到Arduino IDE的开发库里面,重启Arduino程序就可以使用了


      操作方式如图
    • 4 连接arudino uno和enc28j60
    PIN Connections (Using Arduino UNO):
    
    VCC -   3.3V
    GND -    GND
    SCK - Pin 13
    SO  - Pin 12
    SI  - Pin 11
    CS  - Pin  8 # Selectable with the ether.begin() function
    
    最终连线图
    • 5 设置一下本地网络以及arduino的网络,如果用192.168.1.0/24网段,最好把无线网先断了
    // Present a "Will be back soon web page", as stand-in webserver.
    // 2011-01-30 <jc@wippler.nl> http://opensource.org/licenses/mit-license.php
     
    #include <EtherCard.h>
    
    #define STATIC 1  // set to 1 to disable DHCP (adjust myip/gwip values below)
    
    #if STATIC
    // ethernet interface ip address
    static byte myip[] = { 192,168,1,200 };
    // gateway ip address
    static byte gwip[] = { 192,168,1,1 };
    #endif
    
    // ethernet mac address - must be unique on your network
    static byte mymac[] = { 0x74,0x69,0x69,0x2D,0x30,0x31 };
    
    byte Ethernet::buffer[500]; // tcp/ip send and receive buffer
    
    const char page[] PROGMEM =
    "HTTP/1.0 503 Service Unavailable\r\n"
    "Content-Type: text/html\r\n"
    "Retry-After: 600\r\n"
    "\r\n"
    "<html>"
      "<head><title>"
        "Service Temporarily Unavailable"
      "</title></head>"
      "<body>"
        "<h3>This service is currently unavailable</h3>"
        "<p><em>"
          "The main server is currently off-line.<br />"
          "Please try again later."
        "</em></p>"
      "</body>"
    "</html>"
    ;
    
    void setup(){
      Serial.begin(57600);
      Serial.println("\n[backSoon]");
      
      if (ether.begin(sizeof Ethernet::buffer, mymac) == 0) 
        Serial.println( "Failed to access Ethernet controller");
    #if STATIC
      ether.staticSetup(myip, gwip);
    #else
      if (!ether.dhcpSetup())
        Serial.println("DHCP failed");
    #endif
    
      ether.printIp("IP:  ", ether.myip);
      ether.printIp("GW:  ", ether.gwip);  
      ether.printIp("DNS: ", ether.dnsip);  
    }
    
    void loop(){
      // wait for an incoming TCP packet, but ignore its contents
      if (ether.packetLoop(ether.packetReceive())) {
        memcpy_P(ether.tcpOffset(), page, sizeof page);
        ether.httpServerReply(sizeof page - 1);
      }
    }
    
    打开浏览器输入ip地址的效果

    相关文章

      网友评论

        本文标题:arduino通过ENC28J60连接以太网

        本文链接:https://www.haomeiwen.com/subject/qsllrttx.html