ttl接线
1 3.3v
2 RXD
3 GND
4 Txd
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-nand ** ** uboot_ver:0.0.8 **
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Oct 28 2011 - 15:19:29) Marvell version: 3.6.1 - EMC
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00
Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:1024 MB
Found ADT7473, program PWM1 ... OK
Flash: 0 kB
Marvell Serial ATA Adapter
Integrated Sata device found
CPU : Marvell Feroceon (Rev 1)
Found kernel at 0x100000
Found initrd at 0x400000
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x100000, size 0x300000
Reading data from 0x3ff800 -- 100% complete.
3145728 bytes read: OK
NAND read: device 0 offset 0x400000, size 0x400000
Reading data from 0x7ff800 -- 100% complete.
4194304 bytes read: OK
## Booting image at 00040000 ...
Image Name: Linux-2.6.31.8
Created: 2019-06-17 12:13:03 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2502832 Bytes = 2.4 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00900000 ...
Image Name:
Created: 2019-06-17 12:44:09 UTC
Image Type: ARM Linux RAMDisk Image (bzip2 compressed)
Data Size: 2982113 Bytes = 2.8 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
Linux version 2.6.31.8 (soho@bsoho088.iomegacorp.com) (gcc version 4.7.2 (crosstool-NG 1.20.0) ) Mon Jun 17 08:12:59 EDT 2019 v0.0.9 Mon Jun 17 08:12:59 EDT 2019
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 64960
Kernel command line: console=ttyS0,115200 root=/dev/ram0 :::DB88FXX81:eth0:none mtdparts=nand_mtd:0x80000@0(uboot),0x20000@0xa0000(env),0x20000@0xc0000(env2),0x300000@0x100000(uImage),0x400000@0x400000(initrd),0x3f800000@0x800000(boot),1024m@0x0(flash)
PID hash table entries: 1024 (order: 10, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 244352KB available (4592K code, 365K data, 136K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Console: colour dummy device 80x30
Calibrating delay loop... 1589.24 BogoMIPS (lpj=7946240)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
xor: measuring software checksum speed
arm4regs : 1447.200 MB/sec
8regs : 867.600 MB/sec
32regs : 1120.400 MB/sec
xor: using function: arm4regs (1447.200 MB/sec)
NET: Registered protocol family 16
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 256MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
PEX1_MEM ....base e8000000, size 128MB
PEX1_IO ....base f2100000, size 1MB
INTER_REGS ....base f1000000, size 1MB
NFLASH_CS ....base fa000000, size 2MB
SPI_CS ....base f4000000, size 16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size 2MB
Marvell Development Board (LSP Version KW_LSP_5.1.3_patch25)-- DB-88F6282A-BP Soc: 88F6282 A1 LE
Detected Tclk 200000000 and SysClk 533333333
MV Buttons Device Load
Marvell USB EHCI Host controller #0: c8040740
PEX0 interface detected no Link.
PEX1 interface detected no Link.
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
raid6: int32x1 125 MB/s
raid6: int32x2 157 MB/s
raid6: int32x4 162 MB/s
raid6: int32x8 159 MB/s
raid6: using algorithm int32x4 (162 MB/s)
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 2912K
rtc mv_rtc: rtc core: registered kw-rtc as rtc0
RTC registered
XOR registered 4 channels
XOR 2nd invalidate WA enabled
cesadev_init(c000ed58)
mvCesaInit: sessions=640, queue=64, pSram=f0000000
MV Buttons Driver Load
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering unionfs 2.5.11 (for 2.6.31.14)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
msgmni has been set to 483
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for stdrng (krng)
alg: No test for hmac(digest_null) (hmac(digest_null-generic))
async_tx: api initialized (sync-only)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012100 (irq = 34) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Integrated Sata device found
IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
Loading Marvell Ethernet Driver:
o Cached descriptors in DRAM
o DRAM SW cache-coherency
o 2 Giga ports supported
o Single RX Queue support - ETH_DEF_RXQ=0
o Single TX Queue support - ETH_DEF_TXQ=0
o TCP segmentation offload (TSO) supported
o Large Receive offload (LRO) supported
o Receive checksum offload supported
o Transmit checksum offload supported
o Proc tool API enabled
o Rx descripors: q0=256
o Tx descripors: q0=532
o Loading network interface(s):
o register under mv88fx_eth platform
o eth0, ifindex = 2, GbE port = 0
Warning: Giga 1 is Powered Off
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
mvSFlashInit ERROR: Unknown SPI flash device!
ERROR: sflash_probe - Failed to initialize the SFlash.Using Hamming 1-bit ECC for NAND device
NAND flash model -> K9K8G08U0D.
NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 761 at 0x000005f20000
Bad eraseblock 1390 at 0x00000adc0000
Bad eraseblock 7299 at 0x000039060000
7 cmdlinepart partitions found on MTD device nand_mtd
Using command line partition definition
Creating 7 MTD partitions on "nand_mtd":
0x000000000000-0x000000080000 : "uboot"
0x0000000a0000-0x0000000c0000 : "env"
0x0000000c0000-0x0000000e0000 : "env2"
0x000000100000-0x000000400000 : "uImage"
0x000000400000-0x000000800000 : "initrd"
0x000000800000-0x000040000000 : "boot"
0x000000000000-0x000040000000 : "flash"
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
adt7473 0-002e: adt7473 chip found
iBoard_model 2
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
dm_crypt using the OCF package.
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 5
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc mv_rtc: setting system clock to 2021-01-24 00:22:07 UTC (1611447727)
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
RAMDISK: bzip2 image found at block 0
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem) on device 1:0.
Looking for shell in cmdline: console=ttyS0,115200 root=/dev/ram0 :::DB88FXX81:eth0:none mtdparts=nand_mtd:0x80000@0(uboot),0x20000@0xa0000(env),0x20000@0xc0000(env2),0x300000@0x100000(uImage),0x400000@0x400000(initrd),0x3f800000@0x800000(boot),1024m@0x0(flash)
Make node for mtd devices
cat: can't open '/sys/class/block/sda/removable': No such file or directory
cat: can't open '/sys/class/block/sdb/removable': No such file or directory
FLASH based system detected
Create fw_env.config in /etc
Model name is ix2-ng
UBI: attaching mtd5 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd5 to ubi0
UBI: MTD device name: "boot"
UBI: MTD device size: 1016 MiB
UBI: number of good PEBs: 8125
UBI: number of bad PEBs: 3
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 8125
UBI: number of PEBs reserved for bad PEB handling: 81
UBI: max/mean erase counter: 5/4
UBI: image sequence number: 0
UBI: background thread "ubi_bgt0d" started, PID 604
UBI device number 0, total 8125 LEBs (1048320000 bytes, 999.8 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
mdadm: No devices to examine
cat: can't open '/sys/class/block///size': No such file or directory
mdadm: No devices to examine
cat: can't open '/sys/class/block///size': No such file or directory
Valid Disk 1 in md0:
Valid Disk 2 in md0:
USB Device node is /dev/sda1
Checking to see the if the reset button is pressed or not
Checking for valid image on system
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "boot"
UBIFS: file system size: 1035159552 bytes (1010898 KiB, 987 MiB, 8023 LEBs)
UBIFS: journal size: 33546240 bytes (32760 KiB, 31 MiB, 260 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 4952683 bytes (4836 KiB)
md: md0 stopped.
mdadm: stopped /dev/md0
mdadm: /dev/md0 not identified in config file.
No volume groups found
Mount BFDlv to /mnt/boot on ix2-ng NAND
e2fsck 1.42.5 (29-Jul-2012)
ext2fs_check_if_mount: Can't check if filesystem is mounted due to missing mtab file while determining whether /dev/md0_vg/BFDlv is mounted.
e2fsck: No such file or directory while trying to open /dev/md0_vg/BFDlv
Possibly non-existent device?
mount: mounting /dev/md0_vg/BFDlv on sysroot/mnt/boot failed: No such file or directory
Copy dev node to /sysroot/dev
Found Valid EMC Image in disk...
Mounting apps image...
Mounting config image...
Check config filesystem
e2fsck 1.42.5 (29-Jul-2012)
ext2fs_check_if_mount: Can't check if filesystem is mounted due to missing mtab file while determining whether /dev/loop1 is mounted.
Copying System.map...
No need to create fw_env.config
No need to create fw_env.config
Constructing root filesystem...
Bootstrapping ...
rootdir=/
table='/usr/local/cfg/device_table.txt'
makedevs: line 42: chown failed for /bin/busybox: Read-only file system
makedevs: line 49: regular file '/usr/share/udhcpc/default.script' does not exist: No such file or directory
makedevs: line 55: Couldnt create node /dev/null: File exists
makedevs: line 56: Couldnt create node /dev/zero: File exists
makedevs: line 58: Couldnt create node /dev/urandom: File exists
makedevs: line 61: Couldnt create node /dev/loop0: File exists
makedevs: line 61: Couldnt create node /dev/loop1: File exists
makedevs: line 61: Couldnt create node /dev/loop2: File exists
makedevs: line 64: Couldnt create node /dev/console: File exists
makedevs: line 66: Couldnt create node /dev/tty2: File exists
makedevs: line 66: Couldnt create node /dev/tty3: File exists
makedevs: line 66: Couldnt create node /dev/tty4: File exists
makedevs: line 71: Couldnt create node /dev/ttyS0: File exists
makedevs: line 71: Couldnt create node /dev/ttyS1: File exists
makedevs: line 86: Couldnt create node /dev/mtd0: File exists
makedevs: line 86: Couldnt create node /dev/mtd1: File exists
makedevs: line 86: Couldnt create node /dev/mtd2: File exists
makedevs: line 86: Couldnt create node /dev/mtd3: File exists
makedevs: line 86: Couldnt create node /dev/mtd4: File exists
makedevs: line 86: Couldnt create node /dev/mtd5: File exists
makedevs: line 123: Couldnt create node /dev/sda: File exists
makedevs: line 124: Couldnt create node /dev/sda1: File exists
makedevs: line 125: Couldnt create node /dev/sdb: File exists
makedevs: line 126: Couldnt create node /dev/sdb1: File exists
makedevs: line 127: Couldnt create node /dev/sdc: File exists
makedevs: line 128: Couldnt create node /dev/sdc1: File exists
makedevs: line 190: Couldnt create node /dev/md0: File exists
makedevs: line 191: Couldnt create node /dev/md1: File exists
warning: failed to read mtab
Loading ext4...
Loading xfs...
SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
Loading isofs...
Loading udf...
Loading ufsd...
ufsd: module license 'Commercial product' taints kernel.
Disabling lock debugging due to kernel taint
ufsd: driver 8.5 (Jun 17 2019 08:30:02) LBD=ON with delayalloc with ioctl loaded at bf102000
NTFS support included
Hfs+/HfsX support included
Built for: EMC_ix2_2Loading btusb...
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: Generic Bluetooth USB driver ver 0.5
usbcore: registered new interface driver btusb
## Error: "hwdata" not defined
Initialization complete.
Freeing init memory: 136K
INIT: version 2.88 booting
INIT: /etc/inittab[63]: missing action field
Running file /etc/init.d/rcS
Running file /etc/init.d/rc
Running file /etc/rcS.d/S02hostname.sh
Running file /etc/rcS.d/S02mountkernfs.sh
[....] udev requires a kernel >= 2.6.32, not started ... failed!
failed!
Running file /etc/rcS.d/S04mountdevsubfs.sh
Running file /etc/rcS.d/S07hdparm
[....] Setting parameters of disc: (none). ok
Running file /etc/rcS.d/S11hwclock.sh
[info] Setting the system clock.
hwclock: Warning: unrecognized third line in adjtime file
(Expected: `UTC' or `LOCAL' or nothing.)
[info] System Clock set to: Sun Jan 24 00:22:34 UTC 2021.
Running file /etc/rcS.d/S12mtab.sh
Running file /etc/init.d/mountkernfs.sh
Running file /etc/init.d/mountkernfs.sh
Running file /etc/init.d/mountdevsubfs.sh
Running file /etc/init.d/mountdevsubfs.sh
Running file /etc/rcS.d/S30checkfs.sh
[....] Activating lvm and md swap...done.
[....] Checking file systems...fsck 1.42.5 (29-Jul-2012)
done.
Running file /etc/rcS.d/S30procps
[....] Setting kernel variables ...Running file /etc/rcS.d/S35mountall.sh
[....] Mounting local filesystems...done.
[....] Activating swapfile swap...done.
Running file /etc/rcS.d/S36mountall-bootclean.sh
[....] Cleaning up temporary files... /tmp. ok
Running file /etc/rcS.d/S36udev-mtab
dhclient host identical
Running file /etc/rcS.d/S40networking
[....] Configuring network interfaces...done.
Running file /etc/rcS.d/S43rpcbind
[....] Starting rpcbind daemon.... ok
Running file /etc/rcS.d/S44nfs-common
[....] Starting NFS common utilities: statd failed!
Running file /etc/rcS.d/S45mountnfs.sh
Running file /etc/rcS.d/S46mountnfs-bootclean.sh
[....] Cleaning up temporary files.... ok
Running file /etc/rcS.d/S55bootmisc.sh
Running file /etc/rcS.d/S55urandom
INIT: Entering runlevel: 2
Running file /etc/init.d/rc
Running file /etc/rc2.d/S10rsyslog
[....] Starting enhanced syslogd: rsyslogd. ok
Running file /etc/rc2.d/S12dbus
chown: invalid user: `messagebus'
Running file /etc/rc2.d/S20nfs-common
[....] Starting NFS common utilities: statd failed!
Running file /etc/rc2.d/S20nfs-kernel-server
[....] Not starting NFS kernel daemon: no exports. ... (warning).
Running file /etc/rc2.d/S20smartmontools
Running file /etc/rc2.d/S20sysfsutils
[....] Setting sysfs variables.... ok
Running file /etc/rc2.d/S23ntp
[....] Starting NTP server: ntpdRunning file /etc/rc2.d/S25bluetooth
[....] Starting bluetooth: bluetoothd rfcommBluetooth: L2CAP ver 2.13
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
. ok
Starting netplugd...
eth0: started
ln: failed to create symbolic link `/etc/samba/smb.conf': File exists
Generating RSA Key...
unknown key type rsa1
Starting sshd: OK
hostnamed begin to start...
Checking Netwrok interface link status...
Warning : Network Link Is Not Available...
## Error: "hwdata" not defined
hostnamed finished
Starting executord - appmd
export proxy environmental variables
Done.
Running file /etc/rc2.d/S99rc.local
Running file /etc/rc2.d/S99rmnologin
Debian GNU/Linux 7 ix2-dl ttyS0
ix2-dl login: ÿ
网友评论