美文网首页
H3C 交换机配置命令学习

H3C 交换机配置命令学习

作者: 余生似梦 | 来源:发表于2020-04-16 13:40 被阅读0次

    1、开启三层路由功能

    在接口配置模式下

    [H3C] interface g1/0/1
    [H3C-GigabitEthernet1/0/1] port link-mode route \\开启该接口的三层路由功能
    [H3C-GigabitEthernet1/0/1] port link-mode bridge \\关闭该接口的三层路由功能
    

    2、配置交换机接口

    [H3C] interface g1/0/1
    [H3C-GigabitEthernet1/0/1] ip add 192.168.1.1 255.255.0.0
    

    3、配置交换机虚拟接口

    [H3C] interface Vlan-interface 10
    [H3C-Vlan-interface 10] ip add 192.168.1.1 255.255.0.0
    

    4、配置交换机虚拟接口

    配置端口的链路类型为Access类型

    • VLAN视图
    [H3C] vlan 10
    [H3C-vlan10] port interface-list    \\向当前VLAN中添加一个或一组Access端口
    
    • 接口视图
    [H3C-GigabitEthernet1/0/1] port link-type access   //缺省情况下,端口的链路类型为Access
    [H3C-GigabitEthernet1/0/1] port access vlan 10 //将当前Access端口加入到指定VLAN
    

    配置端口的链路类型为Trunk类型

    [H3C-GigabitEthernet1/0/1] port link-type trunk
     缺省情况下,端口的链路类型为Access类型
    
    允许指定的VLAN通过当前Trunk端口
    [H3C-GigabitEthernet1/0/1] port trunk permit vlan { vlan-id-list | all }
     缺省情况下,Trunk端口只允许VLAN 1的报文通过
     
    (可选)设置Trunk端口的缺省VLAN
    [H3C-GigabitEthernet1/0/1]  port trunk pvid vlan vlan-id
     缺省情况下,Trunk端口的缺省VLAN为VLAN 1
    

    静态链路聚合的典型配置

    创建二层聚合端口

    [H3C-A] interface Bridge-Aggregation 1  
    [H3C-A-Bridge-Aggregation1] port link-type trunk
    [H3C-A-Bridge-Aggregation1] port trunk permit vlan 10 20 30
    

    分别将设备A上聚合端口加入到聚合组中

    [H3C-A] interface Ethernet 1/0/1
    [H3C-A-Ethernet1/0/1] port link-type trunk
    [H3C-A-Ethernet1/0/1] port trunk permit vlan 10 20 30
    [H3C-A-Ethernet1/0/1] port link-aggregation group 1
    

    查看链路聚合命令

    [H3C] display link-aggregation verbose
    

    动态聚合模式

    创建二层聚合端口

    [H3C-A] interface Bridge-Aggregation 1  
    [H3C-A-Bridge-Aggregation1] port link-type trunk
    [H3C-A-Bridge-Aggregation1] port trunk permit vlan 10 20 30
    [H3C-A-Bridge-Aggregation1] link-aggreation mode dynamic
    

    配置OSPF

    [H3C]router id 1.1.1.1
    [H3C]ospf 10
    [H3C-ospf-1]area 0
    [H3C-ospf-1-area-0.0.0.0]network 1.1.1.1 0.0.0.0  # 要发布的路由
    

    相关文章

      网友评论

          本文标题:H3C 交换机配置命令学习

          本文链接:https://www.haomeiwen.com/subject/fqlrvhtx.html