美文网首页
华为链路聚合Eth-Trunk/IP-Trunk/MP-Grou

华为链路聚合Eth-Trunk/IP-Trunk/MP-Grou

作者: 王力_9541 | 来源:发表于2019-11-16 14:58 被阅读0次

一、实验拓扑

image.png
  1. R1与R2之间配置PPP串行链路聚合MP-Group
  2. R2与R3之间配置HDLC串行链路聚合IP-Trunk
  3. R1与R3之间配置以太网链路聚合Eth-Trunk

二、设备配置

  1. R1与R2之间配置PPP串行链路聚合MP-Group
  • R1配置
interface Mp-group0/0/0
 ip address 12.1.1.1 255.255.255.0
#
interface Serial0/0/0
 link-protocol ppp
 ppp mp Mp-group 0/0/0
#
interface Serial0/0/1
 link-protocol ppp
 ppp mp Mp-group 0/0/0
#
  • R2配置
interface Mp-group0/0/0
 ip address 12.1.1.2 255.255.255.0
#
interface Serial0/0/0
 link-protocol ppp
 ppp mp Mp-group 0/0/0
#
interface Serial0/0/1
 link-protocol ppp
 ppp mp Mp-group 0/0/0
#
  1. R2与R3之间配置HDLC串行链路聚合IP-Trunk
  • R2配置
interface Ip-Trunk1
 ip address 23.1.1.2 255.255.255.0
#
interface Serial0/0/2
 link-protocol hdlc
 ip-trunk 1
#
interface Serial0/0/3
 link-protocol hdlc
 ip-trunk 1
#
  • R3配置
interface Ip-Trunk1
 ip address 23.1.1.3 255.255.255.0
#
interface Serial0/0/2
 link-protocol hdlc
 ip-trunk 1
#
interface Serial0/0/3
 link-protocol hdlc
 ip-trunk 1
#
  1. R1与R3之间配置以太网链路聚合Eth-Trunk
  • R1配置
interface Eth-Trunk1
 ip address 13.1.1.1 255.255.255.0
#
interface GigabitEthernet0/0/0
 eth-trunk 1
#
interface GigabitEthernet0/0/1
 eth-trunk 1
#
  • R2配置
interface Eth-Trunk1
 ip address 13.1.1.3 255.255.255.0
#
interface GigabitEthernet0/0/0
 eth-trunk 1
#
interface GigabitEthernet0/0/1
 eth-trunk 1
#

三、结果验证

  1. R1与R2之间配置PPP串行链路聚合MP-Group
[R1]display interface Mp-group 0/0/0
Mp-group0/0/0 current state : UP
Line protocol current state : UP
Last line protocol up time : 2019-11-16 09:12:10 UTC-08:00
Description:
Route Port,The Maximum Transmit Unit is 1500
Internet Address is 12.1.1.1/24
Link layer protocol is PPP
LCP opened, MP opened, IPCP opened
Physical is MP, baudrate is 128000 bps
Current system time: 2019-11-16 14:54:41-08:00
    Last 300 seconds input rate 0 bytes/sec, 0 packets/sec
    Last 300 seconds output rate 0 bytes/sec, 0 packets/sec
    Realtime 0 seconds input rate 0 bytes/sec, 0 packets/sec
    Realtime 0 seconds output rate 0 bytes/sec, 0 packets/sec
    9 packets input, 486 bytes, 0 drops
    10 packets output, 500 bytes, 0 drops
    Input bandwidth utilization  :    0%
    Output bandwidth utilization :    0%

[R1]display interface brief 
PHY: Physical
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
(b): BFD down
(e): ETHOAM down
(d): Dampening Suppressed
InUti/OutUti: input utility/output utility
Interface                   PHY   Protocol InUti OutUti   inErrors  outErrors
Eth-Trunk1                  up    up          0%     0%          0          0
  GigabitEthernet0/0/0      up    up          0%     0%          0          0
  GigabitEthernet0/0/1      up    up          0%     0%          0          0
Ethernet0/0/0               down  down        0%     0%          0          0
Ethernet0/0/1               down  down        0%     0%          0          0
GigabitEthernet0/0/2        down  down        0%     0%          0          0
GigabitEthernet0/0/3        down  down        0%     0%          0          0
Mp-group0/0/0               up    up          0%     0%          0          0
  Serial0/0/0               up    up       0.02%  0.02%          0          0
  Serial0/0/1               up    up       0.02%  0.02%          0          0
NULL0                       up    up(s)       0%     0%          0          0
Serial0/0/2                 down  down        0%     0%          0          0
Serial0/0/3                 down  down        0%     0%          0          0
[R1]ping 12.1.1.2
  PING 12.1.1.2: 56  data bytes, press CTRL_C to break
    Reply from 12.1.1.2: bytes=56 Sequence=1 ttl=255 time=30 ms
    Reply from 12.1.1.2: bytes=56 Sequence=2 ttl=255 time=50 ms
    Reply from 12.1.1.2: bytes=56 Sequence=3 ttl=255 time=30 ms
    Reply from 12.1.1.2: bytes=56 Sequence=4 ttl=255 time=40 ms
    Reply from 12.1.1.2: bytes=56 Sequence=5 ttl=255 time=40 ms

  --- 12.1.1.2 ping statistics ---
    5 packet(s) transmitted
    5 packet(s) received
    0.00% packet loss
    round-trip min/avg/max = 30/38/50 ms

[R1]
  1. R2与R3之间配置HDLC串行链路聚合IP-Trunk
display interface Ip-Trunk 1
Ip-Trunk1 current state : UP
Line protocol current state : UP
Last line protocol up time : 2019-11-16 09:16:55 UTC-08:00
Description:
Route Port,Hash arithmetic : According to flow,Maximal BW: 0M, Current BW: 0M, T
he Maximum Transmit Unit is 4470
Internet Address is 23.1.1.2/24  Link layer protocol is nonstandard HDLC
Physical is IP_TRUNK
Current system time: 2019-11-16 14:56:22-08:00
    Last 300 seconds input rate 32 bits/sec, 0 packets/sec
    Last 300 seconds output rate 32 bits/sec, 0 packets/sec
    Realtime 7 seconds input rate 24 bits/sec, 0 packets/sec
    Realtime 7 seconds output rate 24 bits/sec, 0 packets/sec
    Input: 4097 packets,89820 bytes
           4097 unicast,0 broadcast,0 multicast
           0 errors,0 unknownprotocol
    Output:4087 packets,89914 bytes
           4087 unicast,0 broadcast,0 multicast
           0 errors
    Input bandwidth utilization  : 0.02%
    Output bandwidth utilization : 0.02%
-----------------------------------------------------
PortName                      Status      Weight
-----------------------------------------------------
Serial0/0/2                   UP          1
Serial0/0/3                   UP          1
-----------------------------------------------------
The Number of Ports in Trunk : 2
The Number of UP Ports in Trunk : 2

[R2]display interface brief 
PHY: Physical
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
(b): BFD down
(e): ETHOAM down
(d): Dampening Suppressed
InUti/OutUti: input utility/output utility
Interface                   PHY   Protocol InUti OutUti   inErrors  outErrors
Ethernet0/0/0               down  down        0%     0%          0          0
Ethernet0/0/1               down  down        0%     0%          0          0
GigabitEthernet0/0/0        down  down        0%     0%          0          0
GigabitEthernet0/0/1        down  down        0%     0%          0          0
GigabitEthernet0/0/2        down  down        0%     0%          0          0
GigabitEthernet0/0/3        down  down        0%     0%          0          0
Ip-Trunk1                   up    up       0.02%  0.02%          0          0
  Serial0/0/2               up    up       0.02%  0.02%          0          0
  Serial0/0/3               up    up       0.02%  0.02%          0          0
Mp-group0/0/0               up    up          0%     0%          0          0
  Serial0/0/0               up    up       0.02%  0.02%          0          0
  Serial0/0/1               up    up       0.02%  0.02%          0          0
NULL0                       up    up(s)       0%     0%          0          0
[R2]ping 23.1.1.3
  PING 23.1.1.3: 56  data bytes, press CTRL_C to break
    Reply from 23.1.1.3: bytes=56 Sequence=1 ttl=255 time=40 ms
    Reply from 23.1.1.3: bytes=56 Sequence=2 ttl=255 time=50 ms
    Reply from 23.1.1.3: bytes=56 Sequence=3 ttl=255 time=50 ms
    Reply from 23.1.1.3: bytes=56 Sequence=4 ttl=255 time=30 ms
    Reply from 23.1.1.3: bytes=56 Sequence=5 ttl=255 time=60 ms

  --- 23.1.1.3 ping statistics ---
    5 packet(s) transmitted
    5 packet(s) received
    0.00% packet loss
    round-trip min/avg/max = 30/46/60 ms

[R2]
  1. R1与R3之间配置以太网链路聚合Eth-Trunk
[R3]display interface Eth-Trunk1
Eth-Trunk1 current state : UP
Line protocol current state : UP
Last line protocol up time : 2019-11-16 14:45:31 UTC-08:00
Description:
Route Port,Hash arithmetic : According to flow,Maximal BW: 2G, Current BW: 2G, T
he Maximum Transmit Unit is 1500
Internet Address is 13.1.1.3/24
IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is 5489-9875-73c7
Physical is ETH_TRUNK
Current system time: 2019-11-16 14:57:38-08:00
    Last 300 seconds input rate 0 bits/sec, 0 packets/sec
    Last 300 seconds output rate 0 bits/sec, 0 packets/sec
    Realtime 0 seconds input rate 0 bits/sec, 0 packets/sec
    Realtime 0 seconds output rate 0 bits/sec, 0 packets/sec
    Input: 6 packets,550 bytes
           5 unicast,1 broadcast,0 multicast
           0 errors,0 unknownprotocol
    Output:6 packets,550 bytes
           6 unicast,0 broadcast,0 multicast
           0 errors
    Input bandwidth utilization  :    0%
    Output bandwidth utilization :    0%
-----------------------------------------------------
PortName                      Status      Weight
-----------------------------------------------------
GigabitEthernet0/0/0          UP          1
GigabitEthernet0/0/1          UP          1
-----------------------------------------------------
The Number of Ports in Trunk : 2
The Number of UP Ports in Trunk : 2

[R3]display interface brief 
PHY: Physical
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
(b): BFD down
(e): ETHOAM down
(d): Dampening Suppressed
InUti/OutUti: input utility/output utility
Interface                   PHY   Protocol InUti OutUti   inErrors  outErrors
Eth-Trunk1                  up    up          0%     0%          0          0
  GigabitEthernet0/0/0      up    up          0%     0%          0          0
  GigabitEthernet0/0/1      up    up          0%     0%          0          0
Ethernet0/0/0               down  down        0%     0%          0          0
Ethernet0/0/1               down  down        0%     0%          0          0
GigabitEthernet0/0/2        down  down        0%     0%          0          0
GigabitEthernet0/0/3        down  down        0%     0%          0          0
Ip-Trunk1                   up    up       0.02%  0.02%          0          0
  Serial0/0/2               up    up       0.02%  0.02%          0          0
  Serial0/0/3               up    up       0.02%  0.02%          0          0
NULL0                       up    up(s)       0%     0%          0          0
Serial0/0/0                 down  down        0%     0%          0          0
Serial0/0/1                 down  down        0%     0%          0          0
[R3]ping 13.1.1.1
  PING 13.1.1.1: 56  data bytes, press CTRL_C to break
    Reply from 13.1.1.1: bytes=56 Sequence=1 ttl=255 time=10 ms
    Reply from 13.1.1.1: bytes=56 Sequence=2 ttl=255 time=50 ms
    Reply from 13.1.1.1: bytes=56 Sequence=3 ttl=255 time=50 ms
    Reply from 13.1.1.1: bytes=56 Sequence=4 ttl=255 time=50 ms
    Reply from 13.1.1.1: bytes=56 Sequence=5 ttl=255 time=40 ms

  --- 13.1.1.1 ping statistics ---
    5 packet(s) transmitted
    5 packet(s) received
    0.00% packet loss
    round-trip min/avg/max = 10/40/50 ms

[R3]

相关文章

  • 华为链路聚合Eth-Trunk/IP-Trunk/MP-Grou

    一、实验拓扑 R1与R2之间配置PPP串行链路聚合MP-Group R2与R3之间配置HDLC串行链路聚合IP-T...

  • eth-trunk

    一、eth-trunk链路聚合分类 1、手工链路聚合 只能实现活动链路流量的负载分担； 手工完成et...

  • 纯干货分享！链路聚合Eth-trunk详解

    在多个交换机之间有冗余连接的环境中， 可能会发生二层环路，一般会选择使用生成树协议，而开启生成树协议， 必然会阻塞...

  • Linux系统如何配置链路聚合，实现流量负载均衡？

    本文主要解决3个问题： 第一、链路聚合的定义和作用是什么？ 第二、如何配置链路聚合？ 第三、链路聚合的实际应用场景...

  • 锐捷实战系列(二十七) 链路聚合

    实训目的 熟悉链路聚合(AggregatePort)。 实训背景 链路聚合又称端口聚合，是指两台交换机之间在物理上...

  • 链路聚合

    注意事项 只能删除不包含任何成员接口的聚合端口。 二层聚合口成员必须为二层口，三层聚合口成员必须为三层口。 最多可...

  • 链路聚合

  • 链路聚合

    链路聚合是一种提高服务器带宽直接有效的方法。本文的实验环境：交换机型号Dell S4048 ON万兆交换机，服务器...

  • 华为交换机配置聚合链路

    聚合链路简介 聚合链路（Link Aggregation）是一个计算机网络术语，指将多个物理端口汇聚在一起，形成一...

  • 交换机链路聚合与Linux的bond模式对照

    一、整体配置情况： 1、需要手工模式链路聚合：mode0，mode2； 2、需要LACP链路聚合：mode4； 3...

网友评论

      本文标题：华为链路聚合Eth-Trunk/IP-Trunk/MP-Grou

      本文链接：https://www.haomeiwen.com/subject/rdsyictx.html

      延伸阅读

      深度阅读

      • 您也可以注册成为美文阅读网的作者，发表您的原创作品、分享您的心情！

      栏目导航

      热点阅读

      关于我们|服务条款|联系我们|华为链路聚合Eth-Trunk/IP-Trunk/MP-Grou|投稿指南|网站地图|RSS订阅|排版工具|手机版

      提供经典美文摘抄,优美散文欣赏,现代诗歌精选,短篇小说,心情随笔,表白情书范文,故事会在线阅读欣赏

      Copyright © 2014-2023 Haomeiwen.com All Rights Reserved. 好美文阅读网 版权所有

      备案信息：桂公网安备 45052102000051号 · 桂ICP备13007215号-3

      本站所收录作品、热点评论等信息部分来源互联网，目的只是为了系统归纳学习和传递资讯

      所有作品版权归原创作者所有，与本站立场无关，如不慎侵犯了你的权益，请联系我们告知，我们将做删除处理！